|
|
| (2 intermediate revisions not shown) |
| Line 1: |
Line 1: |
| - | ARM/BEAGLE
| |
| - | ----
| |
| | | | |
| - | This page is dedicated to getting MeeGo running on the Beagleboard. More info on the beagleboard can be [http://beagleboard.org/ found here]
| |
| - |
| |
| - | Because the processor for the beagleboard C4 is an OMAP3530 and the N900 currently sports a similar processor, it seems wise to start with the [[ARM]] page.
| |
| - |
| |
| - | = Turn key demo image =
| |
| - | Image shown at the GENIVI meeting during Linux Foundations keynote. It's based on MeeGo 0.9 and has the SGX drivers built-in. XFCE-Desktop, QT demo applications and 3D SGX demos (/usr/bin/SGX) preinstalled.
| |
| - | Just download and write the image to a sdcard (>4GB).
| |
| - |
| |
| - | wget -nd http://ftp.linuxfoundation.org/pub/meego/MEEGO_GENIVI_BEAGLE_DEMO.img.xz
| |
| - | # f222c90ee1279e03f521a750d9e4bd06 MEEGO_GENIVI_BEAGLE_DEMO.img.xz
| |
| - | md5sum MEEGO_GENIVI_BEAGLE_DEMO.img.xz
| |
| - | xz -d MEEGO_GENIVI_BEAGLE_DEMO.img.xz
| |
| - | dd if=<imgfile> of=/dev/sd? # e.g. dd if=MEEGO_BEAGLE_DEMO.img of=/dev/sdc
| |
| - |
| |
| - |
| |
| - | = Steps =
| |
| - | What works so far:
| |
| - | * Take the n900 [http://repo.meego.com/MeeGo/releases/1.0/core/images/meego-n900-open-armv7l/meego-n900-open-armv7l-1.0.0.20100525.1-sda.raw.bz2 rootfs] and extract to the rootfs partition of the beagle sdcard setup. You can mount rootfs of N900 from this image on /mnt by:
| |
| - | *# bunzip meego-n900-open-armv7l-1.0.0.20100525.1-sda.raw.bz2
| |
| - | *# sudo mount -o loop,offset=16384 meego-n900-open-armv7l-1.0.0.20100525.1-sda.raw /mnt
| |
| - | * Then sync the contents to your SDcard by:
| |
| - | *# sudo rsync -aHx /mnt/* /media/your_sd_card
| |
| - | * [http://wiki.meego.com/images/Meego-beagle-kernel.tar.bz2 MeeGo Beagleboard kernel and modules] contains precompiled uImage and kernel modules (v2.6.34) for Beagleboard. You need copy uImage to /boot partition of your SD card, and modules to /lib/modules directory on your root file system.
| |
| - | * Since we are using rootfs tuned for N900, we can stop starting X by replacing id:5:initdefault: to id:3:initdefault: in /etc/inittab.
| |
| - | * To fine tune above kernel follow these instructions:
| |
| - | *# Copy meego-beagle-kernel.config from above archieve to your kernel compilation directory as .config
| |
| - | *# make old_config
| |
| - | *# Tune kernel options using: make xconfig
| |
| - | *# You can now compile your kernel using: make uImage
| |